A、A. the CIR rate of the lowest speed connection multiplied by the number of circuits
B、B. the CIR rate of the lowest speed connection
C、C. the CIR rate of the highest s peed connection
D、D. the sum of all the CIRs divided by the number of connections
更多“EIGRP has been configured to opera te over Frame Relay multipoint connections. What should the bandwidth command be set to?（）”相关的问题
A、The no auto - summary command has not been issued under the EIGRP process on both routers. B、Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24. C、EIGRP cannot exchange routing updates with a neighbor's router interface that is configured with tw o IP addresses. D、EIGRP cannot form neighbor relationship and exchange routing updates with a secondary address.
A、Fa0/0 fails B、The command is rejecteD C、The existing three neighbors fail D、The neighborship with 172.16.2.20 fails and then reestablishes E、None of the other answers is correct
A、 The hostA default gateway has been configured as 10.88.1.10/24. B、 The GLBP weighted load balancing mode has been configured. C、 The GLBP round-robin， load-balancing mode has been configured. D、 The GLBP host-dependent， load-balancing mode has been configured. E、 The hostA default gateway has been configured as 10.88.1.1/24. F、 The hostA default gateway has been configured as 10.88.1.4/24.
A、The no auto - summary command needs to be added under router eigrp 1 B、The subnets keyword was not included in the redistribute command under router ospf 1 C、The metric specified for the redistributed EIGRP routes is too large; m aking the EIGRP routes unreachable by router A D、The default - information originate command needs to be added under router ospf 1 E、The administrative distance of either OSPF or EIGRP must be changed so that EIGRP has a higher administrative distanc e than OSPF
A、R1 has been configured with an ip default- network 2.0.0.0 command. B、R1 has been configured with an ip route 0.0.0.0 0.0.0.0 1.1.1.1 command. C、R1 has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command. D、Another router has been configured with an ip default - network 2.0.0.0 command. E、Another router has been configured with an ip route 2.0.0.0 255.0.0.0 1.1.1.1 command.
A、the ship has been named B、the ship has been built C、the ship has been signed D、the ship has been registered
A、A new default gateway has been setup. B、A new Internet shortcut has been added. C、A new web browser has been installed and is now the default. D、A proxy server has been enabled.
A、EIGRP works on F0/0 and S0/0/0 without further configuration B、EIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modE C、EIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modE D、EIGRP for IPv6 needs at least two more configuration commands before it works on R1
A、the search has found nothing B、the derelict has been found C、the derelict has been located D、the derelict has been sighted
A、R1 will not redistribute 10.1.1.0/24 into EIGRP, because R1 knows it as a connected route and not as an OSPF route. B、For any OS PF routes redistributed into EIGRP, the metric components includea value equivalent to 1 Mbps of bandwidth. C、For any OSPF routes redistributed into EIGRP, the metric components include a value equivalent to 100 microseconds of delay. D、No subnets of network 10.0.0.0 will be redistributed due to the omission of the subnets parameter.
客服
TOP
查看正确答案
