Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（） ipv6 router eigrp 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000::1/64 ipv6 eigrp 1 interface s0/0/0 ipv6 address 2001::/64 eui

第1题

A、hostname R1 B、name R1 C、router name R1 D、name router R1

第2题

[单选题] How do oyu write the current candidate configuration to the permanent storage media?（）

A、[edit] user@router# save /var/tmp/current.conf B、[edit] user@router# write /var/tmp/current.conf C、[edit] user@router# commit /var/tmp/current.conf D、[edit] user@router# dump /var/tmp/current.conf

点击查看答案

第3题

[单选题] How do you write the current candidate configuration to the permanent storage media?（）

A、[edit] user@router# save /var/tmp/current.conf B、[edit] user@router# write /var/tmp/current.conf C、[edit] user@router# commit /var/tmp/current.conf D、[edit] user@router# dump /var/tmp/current.conf

点击查看答案

第4题

[单选题] How do you write the current candidate configuration to the permanent storage media?（）

A、[edit] user@router# save /var/tmp/current.conf B、[edit] user@router# write /var/tmp/current.conf C、[edit] user@router# commit /var/tmp/current.conf D、[edit] user@router# dump /var/tmp/current.conf

点击查看答案

第5题

[] Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （） Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）

A、A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0 B、B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0 C、C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0 D、D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0 E、E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0 F、F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0

点击查看答案

第6题

[多选题] Which series of commands will configure router R1 for LAN-to-LAN communication with router R2？ The enterprise network address is 192.1.1.0/24 and the routing protocol in use is RIP.（）

A、R1（config）# interface ethernet 0；R1（config-if）# ip address 192.1.1.129 255.255.255.192；R1（config-if）# no shutdown B、R1（config）# interface ethernet 0；R1（config-if）# ip address 192.1.1.97 255.255.255.192；R1（config-if）# no shutdown C、R1（config）# interface serial 0；R1（config-if）# ip address 192.1.1.4 255.255.255.252；R1（config-if）# clock rate 56000 D、R1（config）# interface serial 0；R1（config-if）# ip address 192.1.1.6 255.255.255.252；R1（config-if）# no shutdown E、R1（config）# router rip；R1（config-router）# network 192.1.1.4；R1（config-router）# network 192.1.1.128 F、R1（config）# router rip；R1（config-router）# version 2；R1（config-router）# network 192.1.1.0

点击查看答案

第7题

[单选题] Which of the following answers can be verified as true based on the following command output from Router R1?（） R1#show ip ospf virtual - links Virtual Link OSPF_VL0 to router 4.4.4.4 is up Run as demand circuit DoNotAge LSA alloweD. Transit area 1, via interface FastEthernet0/1, Cost of using 3

A、R1 is configured with an area 0 virtual - link 4.4.4.4 cost 3 command. B、The ping 4.4.4.4 command on R1 must currently be successful. C、R1's Fa0/0 OSPF cost is 3. D、4.4.4.4 is known to R1 based on a Type 1 LSA in area 1.

点击查看答案

第8题

[] Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enable Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip o

A、A. RIPng will be enabled on no interfaces. B、B. RIPng will be enabled on one interface. C、C. RIPng will be enabled on two interfaces. D、D. RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.

点击查看答案

第9题

[单选题] Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 /26 and 172.16.1.64 /27. On the basis of the partial output in the exhibit, which statement is true? （）

A、Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised. B、Router R1 will advertise both rou tes. C、Router R1 should be reconfigured with an ACL instead of an ip prefix - list command. D、Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.

点击查看答案

第10题

[单选题] Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0

A、OSPF works on F0/0 and S0/0/0 without further configuration B、OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modE C、OSPF works with the addition of one command: an router - id command in OSPF router configuration modE D、OSPFv3 needs at least two more configuration commands before it works on R1

点击查看答案

请使用微信扫码支付