Router R1 uses S0/0 to connect via a T/1 to the Frame Relay servicE. Five PVCs terminate on the serial link. Three PVCs (101, 102, and 103) are configured on subinterface S0/0.1, and one each (104 and 105) are on S0/0 .2 and S0/0.3. The configuration shows no configuration related to EIGRP WAN bandwidth control, and the bandwidth command is not configured at all.<br /> Which of the following is true about how IOS tries to limit EIGRP's use of bandwidth on S0/0?（）..

第1题

[] Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the omission？（） Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2. Which answer gives the reason for the omission？（）

A、A. R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included. B、B. S0/2 may currently be in a state other than up/up. C、C. The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default. D、D. S0/2 may be configured as a passive inter face.

点击查看答案

第2题

[单选题] Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（） ipv6 router ospf 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000 ::1/64 ipv6 ospf 1 area 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 ospf 1 area 0

A、OSPF works on F0/0 and S0/0/0 without further configuration B、OSPF works with the addition of one command: a no shutdown command in OSPF router configur ation modE C、OSPF works with the addition of one command: an router - id command in OSPF router configuration modE D、OSPFv3 needs at least two more configuration commands before it works on R1

点击查看答案

第3题

[多选题] Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link. Which of the following commands would be needed on R1 to configure eBGP?（）

A、router bgp 2 B、router bgp 1 C、neighbor 10.1 .1.2 remote - as 2 D、neighbor 10.1.1.2 Update - source 10.1.1.1 E、neighbor 10.1.1.2 Update- source S0/0

点击查看答案

第4题

[单选题] Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（） ipv6 router eigrp 1 ipv6 unicast- routing interface f0/0 ipv6 address 2000::1/64 ipv6 eigrp 1 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 eigrp 1

A、EIGRP works on F0/0 and S0/0/0 without further configuration B、EIGRP works with the addition of one command: a no shutdown command in EIGRP router configuration modE C、EIGRP works with the addition of one command: an eigrp router - id command in EIGRP router configurat ion modE D、EIGRP for IPv6 needs at least two more configuration commands before it works on R1

点击查看答案

第5题

[] Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?（） Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?（）

A、A. FEA0::200:FF:FE11:0 B、B. FE80::200:FF:FE11:1111 C、C. FE80::0213:19FF:FE7B:0:1 D、D. FEB0::211:11FF:FE11: 1111

点击查看答案

第6题

[] Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip one enable ipv6 address 2000::1/64 interface s0/0/0 ipv6 address 2001::/64 eui - 64 ipv6 rip one enable Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（） ipv6 unicast- routing interface f0/0 ipv6 rip o

A、A. RIPng will be enabled on no interfaces. B、B. RIPng will be enabled on one interface. C、C. RIPng will be enabled on two interfaces. D、D. RIPng will advertise about prefixes connected to S0/0/0 and F0/0, but only send Updates on one interface.

点击查看答案

第7题

[多选题] Examine the following configuration on Router R1. R1's show ip route 172.16.4.1 command list s a route with outgoing interface S0/1/1. Host 172.16.3.3 uses telnet to connect to host 172.16.4.1.What will Router R1 do with the packets generated by host 172.16.3.3 because of the telnet,assuming the packets enter R1's F0/0 interface?（） interface Fastethernet 0/0 ip address 172.16.1.1 255.255.255.0 ip policy route - map Q2 ! route - map Q2 permit match ip address 101 set interface s0/0/1 ! access - list 101 permit tcp host 172.16.3.3 172.16.4.0 0.0.0.255

A、The packet will be forwarded out S0/0 /1, or not at all. B、The packet will be forwarded out S0/0/1 if it is up. C、The packet will be forwarded out S0/1/1 if it is up. D、The packet will be forwarded out S0/1/1 if it is up, or if it is not up, out s0/0/1. E、The packet will be forwarded o ut S0/0/1 if it is up, or if it is not up, out s0/1/1.

点击查看答案

第8题

[单选题] Which of the following commands would you use, to configure a default route to any destination NOT found in the routing table?（）

A、Router(config)# ip default-route 0.0.0.0 255.255.255.255 s0 B、Router(config)# ip route 0.0.0.0 255.255.255.255 s0 C、Router(config)# ip default-route 0.0.0.0 0.0.0.0 s0 D、Router(config)# ip route 0.0.0.0 0.0.0.0 s0 E、Router(config)# ip route any any e0

点击查看答案

第9题

[单选题] Host 1 sends a request for a file to remote sever1. Which destination address does Host 1 place f the packet containing the request（）。

A、The Mac address of the NIC in Sever1 B、The IP address of Server 1. C、The MAC address of the s0/0/0 interface of router R2 D、The IP address of the s0/0/0 interface of router R1 E、The IP address of the Fa0/0 interface of router R1

点击查看答案

请使用微信扫码支付