Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link.<br /> Which of the following commands would be needed on R1 to configure eBGP?（）..

第1题

[多选题] Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise. Which of the following is most likely to be useful on the branch router?（）

A、IPsec tunnel B、GRE tunnel C、Floating stati c route D、An IGP

点击查看答案

第2题

[] Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE. Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（） Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE. Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）

A、A. Privacy B、B. Authentication C、C. Allows using an IGP between R1 and the Enterprise D、D. Secure communications

点击查看答案

第3题

[单选题] Refer to the exhibit. ROUTE Enterprises has many stub networks in their enterprise network, such as router B and its associated network. EIGRP is to be implemented on router A so that neither the prefix for the S/0/0/0 interface nor the prefixes from router B appear in the routing tables for the router in the enterprise network. Which action will accomplish this goal?（）

A、Declare router B a stub router using the eigrp stub command. B、Use the passive - interface command for interface Serial0/0/0. C、Use a mask with the network command to exclude interface Serial0/0/0. D、Implement a distribute list to exclude the link prefix from the routi ng updates.

点击查看答案

第4题

[单选题] Router R-1 is configured for BGP routing as shown below： router bgp 65300network 27.0.0.0neighbor 192.23.1.1 remote-as 65300 From the perspective of router R-1， what kind of router is the router with IP address 192.23.1.1？（）

A、A peer router running IBGP B、A peer router running EBGP C、A community member running IBGP D、A peer group member running IBGP E、A peer group member running EBGP

点击查看答案

第5题

[单选题] Refer to the exhibit The neighbor 10.1.1.1 weight 200 BGP configuration command has been configured on router A. What will be the result of this configuration? （）

A、Router A will prefer the path through router B for network 172.20.0.0 B、Router A will prefer the path through router C for network 172.20.0.0 C、Packets from router D will prefer the path through router B for networks advertised by router A D、Packets from r outer D will prefer the path through router C for networks advertised by router A

点击查看答案

第6题

[] Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （） Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）

A、A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0 B、B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0 C、C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0 D、D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0 E、E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0 F、F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0

点击查看答案

第7题

[单选题] 管理员想在MSR路由器上配置OSPF路由优先级值为100，则下列哪条命令是正确的？（）

A、[Router]ospf preference 100 B、R[outer]preference 100 C、[Router-ospf-1]ospf preference 100 D、[Router-ospf-1]preference 100

点击查看答案

第8题

[单选题] Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively. Which of the following commands would not be part of a working eBGP confi guration on Router R1?（）

A、router bgp 1 B、neighbor 2.2.2.2 remote- as 2 C、neighbor 2.2.2.2 update - source loopback1 D、neighbor 2.2.2.2 multihop 2

点击查看答案

第9题

[单选题] The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（） B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18

A、This router has set the Weight of this route to 10. B、This router's BGP table lists this route as an iBGP route. C、This router's MED has been set to 10. D、This router's BGP table lists an AS_Path length of 10 for this route.

点击查看答案

第10题

[多选题] What are three methods for managing a Juniper Enterprise Router?（）

A、CU B、SDX C、SAP D、J-Web E、J-Config

点击查看答案

请使用微信扫码支付