Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）..

第1题

[多选题] Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. The single serial link b etween the two routers uses IP addresses 10.1.1.1 and 10.1.1.2, respectively. Both routers use their S0/0 interfaces for this link. Which of the following commands would be needed on R1 to configure eBGP?（）

A、router bgp 2 B、router bgp 1 C、neighbor 10.1 .1.2 remote - as 2 D、neighbor 10.1.1.2 Update - source 10.1.1.1 E、neighbor 10.1.1.2 Update- source S0/0

点击查看答案

第2题

[单选题] Enterprise Router R1, in ASN 1, connects to ISP Router I1, ASN 2, using eBGP. There are two parallel serial links between the two rou ters. The implementation plan calls for each router to base their BGP TCP connection on their respective loopback1 interfaces, with IP addresses 1.1.1.1 and 2.2.2.2, respectively. Which of the following commands would not be part of a working eBGP confi guration on Router R1?（）

A、router bgp 1 B、neighbor 2.2.2.2 remote- as 2 C、neighbor 2.2.2.2 update - source loopback1 D、neighbor 2.2.2.2 multihop 2

点击查看答案

第3题

[] Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（） interface f0/0 ipv6 address 2345:0:0:8::1/64 Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（） interface f0/0 ipv6 address 2345:0:0:8::1/64

A、A. 2345:0:0:8::1 B、B. 2345:0:0:8:0:FF:FE11:1111 C、C. FE80::8:0:FF:FE11:1111 D、D. FE80:0:0:8::1

点击查看答案

第4题

[] Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （） Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）

A、A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0 B、B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0 C、C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0 D、D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0 E、E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0 F、F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0

点击查看答案

第5题

[单选题] Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）

A、Add the area 1 stub command on routers R1. B、Add the always keyword to the default - information originate configuration command on router R2. C、Remov e the default information originate configuration command from router R2 and place it on router R1. D、Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

点击查看答案

第6题

[] Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?（） Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router. Which of the following could be the link local address of R1's interface S0/0?（）

A、A. FEA0::200:FF:FE11:0 B、B. FE80::200:FF:FE11:1111 C、C. FE80::0213:19FF:FE7B:0:1 D、D. FEB0::211:11FF:FE11: 1111

点击查看答案

第7题

[] The following command output was gathered from Router R1, an ABR between areas 0 (backbone) and area 1. In this internetwork, area 0 contains all the subnets of cla ss A network 10.0.0.0. R1's OSPF process has a distribute - list prefix question in command configured. Assuming the subnets listed in the answers actually exist in area 0. Which of the following occurs on router R1?（） R1#sh ip prefix - list ip prefix - list question: 4 entries seq 5 deny 10.1.2.0/24 ge 25 le 27 seq 15 deny 10.2.0.0/16 ge 30 le 30 seq 20 permit 0.0.0.0/0 le 32 The following command output was gathered from Router R1, an ABR between areas 0 (backbone) and area 1. In this internetwork, area 0 contains all the subnets of cla ss A network 10.0.0.0. R1's OSPF process has a distribute - list prefix question in command configured. Assuming the subnets listed in the answers actually exist in area 0. Which of the following occurs on router R1?（） R1#sh

A、A. R1 will not create/flood a type 3 LSA for subnet 10.1.2.0/26 into area 1 B、B. R1 will not create/flood a Type 3 LSA for subnet 1 0.1.2.0/24 into area 1 C、C. R1 will not have an OSPF route for subnet 10.1.2.0/26 in its IP routing tablE D、D. R1 will not have an OSPF route for subnet 10.1.2.0/24 in its IP routing tablE

点击查看答案

第8题

[单选题] Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 /26 and 172.16.1.64 /27. On the basis of the partial output in the exhibit, which statement is true? （）

A、Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised. B、Router R1 will advertise both rou tes. C、Router R1 should be reconfigured with an ACL instead of an ip prefix - list command. D、Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.

点击查看答案

第9题

[多选题] Which series of commands will configure router R1 for LAN-to-LAN communication with router R2？ The enterprise network address is 192.1.1.0/24 and the routing protocol in use is RIP.（）

A、R1（config）# interface ethernet 0；R1（config-if）# ip address 192.1.1.129 255.255.255.192；R1（config-if）# no shutdown B、R1（config）# interface ethernet 0；R1（config-if）# ip address 192.1.1.97 255.255.255.192；R1（config-if）# no shutdown C、R1（config）# interface serial 0；R1（config-if）# ip address 192.1.1.4 255.255.255.252；R1（config-if）# clock rate 56000 D、R1（config）# interface serial 0；R1（config-if）# ip address 192.1.1.6 255.255.255.252；R1（config-if）# no shutdown E、R1（config）# router rip；R1（config-router）# network 192.1.1.4；R1（config-router）# network 192.1.1.128 F、R1（config）# router rip；R1（config-router）# version 2；R1（config-router）# network 192.1.1.0

点击查看答案

Router R1, in ASN 11, learns a BGP route from BGP peer R22 in ASN 22. R1 and then uses BGP to advertise the route to R2, also in ASN 11. What ASNs would you see in the BGP table on R2 for this route?（）

请使用微信扫码支付