In the output of show isis adjacency, which three can be displayed under the attributes header? （）

A、NET

B、IS type

C、overload

D、attached

E、area addresses

查看正确答案

更多“In the output of show isis adjacency, which three can be displayed under the attributes header? （）”相关的问题

第1题

[单选题] The frequency output of an operating alternator is controlled by the （）.

A、relative speed of the rotor poles B、number of turns of wire in the armature coil C、strength of the magnets used D、output voltage

点击查看答案

第2题

[单选题] The frequency output of an operating alternator is controlled by the （）.

A、relative speed of the rotor poles B、number of turns of wire in the armature coil C、strength of the magnets used D、output voltage

点击查看答案

第3题

[单选题] The fol lowing line of output was extracted from the output of the show ip bgp command on Router R1. Which of the following can be determined from this output?（） Network Next Hop Metric LocPrf Weight Path * 130.1.1.0/28 1.1.1.1 0 1 2 3 4 i

A、The route is learne d from an eBGP peer B、The route has no more than three ASNs in the AS_PatH C、The route is the best route for this prefix D、None of these facts can be positively determined by this output

点击查看答案

第4题

[] A verification plan shows a network diagram with branch office Routers B1 through B100, plus two ABRs, ABR1, and ABR2, all in area 100. The branches connect to the ABRs using Frame Relay point - to - point subinterfaces. The verification plan lists the output of the show i p ospf database summary 10.100.0.0 command on a router B1, one of the branches. Which of the following is true regarding the output that could be listed for this command?（） A verification plan shows a network diagram with branch office Routers B1 through B100, plus two ABRs, ABR1, and ABR2, all in area 100. The branches connect to the ABRs using Frame Relay point - to - point subinterfaces. The verification plan lists the output of the show i p ospf database summary 10.100.0.0 command on a router B1, one of the branches. Which of the following is true regarding the output that could be listed for this command?（）

A、A. The output lists nothing unless 10.100.0.0 has been configured as a summary rou te using the area range command. B、B. If 10.100.0.0 is a subnet in area 0, the output lists one Type 3 LSA, specifically the LSA with the lower metric when comparing ABR1's and ABR2's LSA for 10.100.0.0. C、C. If 10.100.0.0 is a subnet in area 0, the output lists two Type 3 LSAs, one each created by BR1 and ABR2. D、D. None, because the Type 3 LSAs would exist only in the ABR's LSDBs.

点击查看答案

第5题

[] An operational amplifier, as used in todays consoles, has a calculated gain of 5This means that when the input changes （）

A、A.5 volts, the output changes 10 volts B、B.10 volts, the output changes 5 volts C、C.2 volts, the output changes 10 volts D、D.10 volts, the output changes 2 volts

点击查看答案

第6题

[单选题] One factor that determines the frequency of an alternator is the（）.

A、number of turns of wire in the armature coil B、number of magnetic poles C、strength of the magnets used D、output voltage

点击查看答案

第7题

[单选题] One factor that determines the frequency of an alternator is the（）.

A、number of turns of wire in the armature coil B、number of magnetic poles C、strength of the magnets used D、output voltage

点击查看答案

第8题

[] An operational amplifier, as used in todays consoles, may have a calculated gain of 5√This means that as the input changes by （）

A、A.1 volt, the output changes 5 volts B、B.5 volts, the output changes 1 volt C、C.5 volts, the output changes 10 volts D、D.10 volts, the output changes 5 volts

点击查看答案

第9题

[单选题] The frequency of an alternator at a given RPM is determined by the （）.

A、number of turns of wire in the armature coil B、number of magnetic poles C、strength of the magnets used D、output voltage

点击查看答案

第10题