The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below: Gateway of last resort is 10.1.2.2 to network 0.0.0.0 10.0.0.0/24 is subnetted, 2 subnets R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0 C 10.1.2.0 is directly connected, Serial0/0 C 10.1.5.0 is directly connected, Serial0/1 C 10.1.6.0 is directly connected, FastEthernet0/0 R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1 Based on the output above, if an administrator pings host 10.1.8.5 from host 10.1.6.100, how will the router TestkingA process the ICMP packets?（）..

第1题

[单选题] The relevant configuration files for the TestKing1 and TestKing2 routers are displayed below: With due consideration to the command outputs, which of the following reasons would you attribute the connectivity problem between the two routers?（）

A、The authentication needs to be changed to PAP for both routers. B、The serial IP addresses of routers are not on the same subnet. C、The username/password combination is incorrectly configured. D、The router names are incorrectly configured.

点击查看答案

第2题

[单选题] A technician at TestKing needs to update the network documentation. One of the tasks includes documenting the name of the IOS image file of each router in the network.Which commands could be used to find this information?（）

A、Router# show protocols B、Router# show version C、Router# show image D、Router# show IOS E、Router# show flash

点击查看答案

第3题

[多选题] Part of the configuration files for routers testking1 and testking2 are displayed below: If you were to enter the "show interface serial 0" command on router testking1,which of the following will be displayed?（）

A、Serial 0 is down, line protocol is down B、Serial 0 is up, line protocol is up C、Open: IPCP, CDPCP D、LCP closed E、LCP open

点击查看答案

第4题

[单选题] Exhibit: The following are true with one of the TestKing routers: 1) The IOS image in flash is missing 2) No Network connectivity is available. 3) The router fallback IOS image is corrupt. How will this Cisco 2600 series router respond if the conditions listed in the exhibit exist during the boot process?（）

A、The router will enter setup mode. B、The router will enter ROM monitor mode. C、The router will enter global configuration mode. D、The boot will hang until an IOS is available.

点击查看答案

第5题

[] TestKing.com has a large corporate network that uses multiple routing protocols.Hosts in a portion of the network that uses EIGRP have become unreachable.Which router command will allow you, the network technician, to view the status of these routes?（）

A、A. TestKing# show eigrp entries B、B. TestKing# show protocols C、C. TestKing# debug eigrp routes D、D. TestKing# show ip route eigrp E、E. TestKing# show route eigrp

点击查看答案

第6题

[单选题] The routers named Testking1 and Testking2 are both configured with RIP only.What will happen in the event of Testking1 receiving a routing update that contains a higher cost path to a network already in its routing table?（）

A、The update information will be added to the existing routing table. B、The update information will replace the existing routing table entry. C、The update will be ignored and thus no further action will occur. D、The existing routing table entry will be purged from the routing table and all routers will attempt convergence.

点击查看答案

第7题

[单选题] There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers: From your observations of the above exhibit, what is the underlying cause of the problem?（）

A、The loopback is not set. B、The serial cable is faulty. C、The subnet mask is not configured properly. D、The IP address is not configured properly. E、The Layer 2 frame types are not compatible. F、The keepalive setting is not configured properly.

点击查看答案

第8题

[单选题] You try to add a new router into the established Testking OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers.The new router was configured for OSPF in the following way: Router(config)# router ospf 99 Router(config-if)# network 10.0.0.0 255.0.0.0 area 0 Based on this information, what is the most likely problem?（）

A、The process id is configured improperly. B、The OSPF area is configured improperly. C、The network wildcard mask is configured improperly. D、The network number is configured improperly. E、The AS is configured improperly. F、The network subnet mask is configured improperly. H、All of the above are likely problems.

点击查看答案

第9题

[单选题] TestKing has 25 computers and decides to connect the network to the Internet.TestKing would like for all of the computers to have access to the Internet at the same time, but TestKing only has four usable publicly routable IP addresses.What should be configured on the router so that all computers can connect to the Internet simultaneously?（）

A、Static NAT B、Global NAT C、Dynamic NAT D、Static NAT with ACLs E、Dynamic NAT with overload

点击查看答案

第10题

[单选题] You are the network administrator for TestKing.com. All network servers run Windows Server 2003. The network includes a file server named Testking1. Testking1 contains a single disk for system files and two SCSI hard disks that comprise a 72-GB mirrored volume with 65 GB of read-only data. Users connect to this data by using shortcuts on their desktops. Testking1 is scheduled for replacement. You have a scheduled maintenance window to complete this task. Before the maintenance window, you build a new server. You need to bring the new server online with current data and re-establish redundancy as quickly as possible. You must also ensure that the desktop shortcuts will continue to function. What should you do?（）

A、Name the new server Testking1. Create a new mirrored volume by using two 72-GB disks. Connect Testking2 to the network and copy the data from Testking1. When copying is complete, shut down the old Testking1. B、Name the new server Testking1. Move both disks from the old Testking1 to the new Testking1. Scan the disks for changes. Import the disks.Connect the new Testking1 to the network. C、Name the new server Testking1. Break the mirror on the old Testking1. Move one of the disks from the old Testking1 to the new Testking1. Scan the disk for changes. Initialize the disk. Select the spare disk and create the mirror. Connect the new Testking1 to the network. D、Name the new server Testking1. Remove one of the disks in the mirror from the old Testking1. Move the disk on the new Testking1. Scan the disk for changes. Import the disk, Shut down the old Testking1 and connect the new Testking1 to the network.

点击查看答案

请使用微信扫码支付