搜题

【多选题】

To configure the VLAN trunking protocol to communicate VLAN information between two switches, what two requirements must be met? （）

A、Each end of the trunk line must be set to IEEE 802.1E encapsulation.

B、The VTP management domain name of both switches must be set the same.

C、All ports on both the switches must be set as access ports.

D、One of the two switches must be configured as a VTP server.

E、A rollover cable is required to connect the two switches together.

F、A router must be used to forward VTP traffic between VLANs.

查看正确答案

更多“To configure the VLAN trunking protocol to communicate VLAN information between two switches, what two requirements must be met? （）”相关的问题

第1题

[多选题] Referring to the exhibit, what are two differences between the active and candidate configurations?（）

A、The ge-0/0/0 interface was added to the candidate configuration. B、Area 0 was added to the active configuration. C、Area 1 was added to the candidate configuration. D、The ge-0/0/0 interface was added to the active configuration.

点击查看答案

第2题

[单选题] Assuming the default switch configuration,which approach should you use to configure the extended vlan range(1006 through 4094) on a cisco catalyst 3750 series switch?（）

A、Configure the switch to be in VTP client mode. B、Configure the switch to be in VTP domaint mode. C、Configure the switch to be in VTP transparent mode. D、Configure the switch to be in VTPv2.

点击查看答案

第3题

[单选题] Assuming the default switch configuration,which approach should you use to configure the extended vlan range(1006 through 4094) on a cisco catalyst 3750 series switch?（）

点击查看答案

第4题

[单选题] Which additional configuration step is necessary in order to connect to an access point that has SSID broadcasting disabled（）。

A、Set the SSID value in the client software to public. B、Configure open authentication on the AP and the client. C、Set the SSID value on the client to the SSID configured on the AP. D、Configure MAC address filtering to permit the client to connect to the AP.

点击查看答案

第5题

[] Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? （） Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? （）

A、A.The Router1 WAN port is configured as a trunking port. B、B.The Router1 port connected to Switch1 is configured using subinterfaces. C、C.The Router1 port connected to Switch1 is configured as 10 Mbps. D、D.The Switch1 port connected to Router1 is configured as a trunking port. E、E.The Switch1 port connected to Host B is configured as an access port. F、F.The Switch1 port connected to Hub1 is configured as full duplex.

点击查看答案

第6题

[] Which additional configuration step is necessary in order to connect to an access point that has SSID broadcasting disabled?（）

A、A.Set the SSID value in the client software to public. B、B.Configure open authentication on the AP and the client. C、C.Set the SSID value on the client to the SSID configured on the AP. D、D.Configured MAC address filtering to permit the client to connect to the AP.

点击查看答案

第7题

[] Which additional configuration step is necessary in order to connect to an access point that has SSID broadcasting disabled?（）

A、A. Set the SSID value in the client software to public. B、B. Configure open authentication on the AP and the client. C、C. Set the SSID value on the client to the SSID configured on the AP. D、D. Configured MAC address filtering to permit the client to connect to the AP.

点击查看答案

第8题

[单选题] Refer to the exhibit.All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?（）

A、The access link needs to be configured in multiple VLANs. B、The link between the switches is configured in the wrong VLAN. C、The link between the switches needs to be configured as a trunk. D、VTP is not configured to carry VLAN information between the switches. E、Switch IP addresses must be configured in order for traffic to be forwarded between the switches

点击查看答案

第9题

[] A new LPAR has been created that needs SAN attached disk for a database. After AIX has been installed, the fibre cables are attached to the adapters. How should the administrator configure the disks?（） A new LPAR has been created that needs SAN attached disk for a database. After AIX has been installed, the fibre cables are attached to the adapters. How should the administrator configure the disks?（）

A、A.Run 'mkdev' to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run 'cfgmgr' to discover and configure the disks. B、B.Run 'mkpath' to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run 'cfgmgr' to discover and configure the disks. C、C.Run 'chpath' to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run 'cfgmgr' to discover and configure the disks. D、D.Run 'cfgmgr' to force the FC adapter to log into the SAN, have the SAN LUNs zoned to the server, run 'cfgmgr' to discover and configure the disks.

点击查看答案

第10题

[单选题] You are the network administrator for The network consists of a single Active Directory domain named All network servers run Windows Server 2003, and all client computers run Windows XP Professional. You create and share a folder named Sales on a member server. You apply the default share permission and NTFS permissions to Sales. Then you create a folder named SalesForecast in Sales. You apply the default NTFS permissions to SalesForecast. Managers in the sales department are members of a domain user group named SalesManagers. When members of SalesManagers try to add files to SalesForecast,they receive the "Access is denied" error message. You need to configure permissions on these folders to fulfil the following requirements: 1. Members of SalesManagers must be able to create, modify, and delete files in both folders. 2. All other domain users must only be able to read files in both folders. What should you do?（）

A、Configure the share permissions on Sales to assign the Allow - Change permission to the Everyone group. Configure the NTSF permissions on SalesForecast to assign the Allow - Write permission to the SalesManagers group. B、Configure the share permissions on Sales to assign the Allow - Change permissions to the SalesManagers group. Configure the NTSF permissions on Sales to assign the Allow - Write permissions to the SalesManagers group. C、Configure the share permissions on Sales to assign the Allow - Change permissions to the Everyone group. Configure the NTFS permissions on Sales to assign the Allow - Modify permission to the SalesManagers group. D、Configure the share permissions on Sales to assign theAllow - Change permission to the SalesManagers group. Configure the NTFS permissions on Sales to assign the Allow - Modify permission to the SalesManagers group.

点击查看答案

账号：登录

答题记录

我的收藏

我的题库

客服

TOP

请使用微信扫码支付

订单号：
遇到问题请联系在线客服