搜题
用户您好， 请在下方输入框内搜索其它题目：
搜题
题目内容 （请给出正确答案）
提问人：网友 发布时间：
【单选题】

The interface between the liquid seal (water) and the oil should be positioned （） possible to the bowl periphery.

A、as far as

B、as soon as

C、as close as

D、as closer as

查看正确答案
更多“The interface between the liquid seal (water) and the oil should be positioned （） possible to the bowl periphery.”相关的问题
第1题
[多选题] To troubleshoot interface problems, you can use both the disable command and the deactivate command. Which two statements are correct?（）

A、If the interface is disabled, the logical unit will administratively shutdown.  B、If the interface is deactivated, the physical interface will administratively shutdown.  C、If the interface is deactivated, the interface configuration is ignored during commit.  D、If the interface is disabled, the logical unit configuration is ignored during commit.  

点击查看答案
第2题
[单选题] Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured. Which combinations accurately describe the interface under which a feature will be configured?（）

A、PPP on the ATM interface  B、VPI/VCI on the dialer interface  C、IP address on the ATM interface  D、CHAP on the dialer interface  

点击查看答案
第3题
[多选题] Which three route filtering statements are true?（）

A、After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interface  B、When you use the passive - interface command with RIPv2, multicasts are sent out the specified interface  C、After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interface  D、When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interface  E、After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interface  F、When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface  

点击查看答案
第4题
[单选题] What is  the default metric used on IS -IS routers for each interface?（）

A、The cost is set to 10 for all interfaces.  B、The cost is set to 10 for LAN interfaces and 20 for WAN interfaces.  C、The cost is based on the speed of the interface.  D、The cost is based o n a composite of bandwidth and delay of the interface.  

点击查看答案
第5题
[单选题] Which interface is used for RTO synchronization and forwarding traffic between the devices in a cluster?（）

A、the st interface  B、the reth interface  C、the fxp1 and fxp0 interfaces  D、the fab0 and fab1 interfaces  

点击查看答案
第6题
[单选题] A network administrator creates a layer 3 EtherChannel, bundling four interfaces into channel group 1. On what interface is the IP address configured?（）

A、the port-channel 1 interface  B、the highest number member interface  C、all member interfaces  D、the lowest number member interface  

点击查看答案
第7题
[单选题] Refer to the exhibit.Assuming that the entire network topology is shown, what is the operational status of the interfaces of R2 as indicated by the command output shown?（）

A、One interface has a problem.  B、Two interfaces have problems.  C、The interfaces are functioning correctly.  D、The operational status of the interfaces cannot be determined from the output shown.  

点击查看答案
第8题
[单选题] If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?（）

A、the IP address of the first Fast Ethernet interface  B、the IP address of the console management interface  C、the highest IP address among its active interfaces  D、the lowest IP address among its active interfaces  E、the priority value until a loopback interface is configured  

点击查看答案
第9题
[单选题] On the assumption that every OSPF router in a particular area is configured with there is no loopback interface set?（）

A、The IP address of the first Fast Ethernet interface.  B、The IP address of the console management interface.  C、The highest IP address among its active interfaces.  D、The lowest IP address among its active interfaces.  E、There will be no router ID until a loopback interface is configured.  

点击查看答案
第10题
[多选题] Which two statements are true about the primary address on an interface?（）

A、It is the address used by default as the local address for broadcast and multicast packets sourced locally and sent out of the interface  B、You use the primary address when you have multiple IP addresses belonging to the same subnet on the same interface  C、It can be useful for selecting the local address used for packets sent out of unnumbered interfaces when multiple non-127 addresses are configured on the loopback interface  D、By default, the primary address on an interface is selected as the numerically highest local address configured on the interface  

点击查看答案
账号：
答题记录 我的收藏 我的题库
客服
TOP

请使用微信扫码支付

订单号：
遇到问题请联系在线客服