搜题

【单选题】

Because the top of the connecting rod swings about the pin and changes direction each time the piston reaches mid-stroke, the relative speed between bearing and pin at mid-stroke is zero, （）to a maximum as the piston approaches top or bottom dead center and then （） back to zero again as the piston approaches mid-stroke and the connecting rod changes direction.

A、accelerates；decelerates

B、accelerates；accelerates

C、decelerates；decelerates

D、decelerates；accelerates

查看正确答案

更多“Because the top of the connecting rod swings about the pin and changes direction each time the piston reaches mid-stroke, the relative speed between bearing and pin at mid-stroke is zero, （）to a maximum as the piston approaches top or bottom dead center and then （） back to zero again as the piston approaches mid-stroke and the connecting rod changes direction.”相关的问题

第1题

[单选题] Because of the resulting higher pressures in the cylinder from the combustion of this greater mass of fuel, and the larger diameters, the liner must be made （） at the top to accommodate the higher stresses, and prevent cracking of the material.

A、thinner B、thicker C、smoother D、rougher

点击查看答案

第2题

[单选题] A vessel has an amidships superstructure. Which location would be most suitable for ondeck stowage of automobiles?（）.

A、On top of No.1 hatch B、Beside the hatches, forward of the midships house C、On top of the hatch immediately forward of the midships house D、On top of the hatch immediately aft of the midships house

点击查看答案

第3题

[单选题] （）mooring,sailors put the rat guard on the moorings.

A、In the end of B、At the end of C、On top of D、At the top of

点击查看答案

第4题

[单选题] A vessel has an amidships superstructure. Which location would be most suitable for on-deck stowage of automobiles?（）.

A、On top of No.1 hatch B、Beside the hatches，forward of the midships house C、On top of the hatch immediately forward of the midships house D、On top of the hatch immediately aft of the midships house

点击查看答案

第5题

[单选题] The clearance volume for a single stage compressor is defined as the space created between the （）.

A、top of the piston and bottom side of head, with the piston at BDC B、piston and head, including the space around the piston to the top of the upper ring and under the valves, with the piston at TDC C、bottom of the piston and bottom side of the head at TDC, regardless of upper ring location and valve placement D、top of the piston and bottom side of the head at TDC as compared to that which exists between the top of the piston and bottom side of head at BDC

点击查看答案

第6题

[单选题] Molded depth is measured from the（）.

A、inside of the shell B、outside of the shell C、top of the center vertical keel D、top of the garboard stake

点击查看答案

第7题

[单选题] Why is the southern area of the Northern Territory called the Red Centre of Australia?（）

A、Because Uluru is located there. B、Because it is extremely hot and dry. C、Because it consists of miles and miles of red-sand desert and mountain ranges. D、Because it lies in the tropics.

点击查看答案

第8题

[单选题] The atmosphere in a tank is too lean if it is（）.

A、incapable of supporting combustion because the hydrocarbon content is below the LFL (Lower Flammable Limit) B、capable of supporting combustion because the hydrocarbon content is above the UFL (Upper Flammable Limit) C、capable of supporting a fire once started D、not safe for ballasting

点击查看答案

第9题

[单选题] Ullage measurements are taken from the top of the liquid to（）.

A、the base of the expansion trunk B、the base of the ullage port C、a line scribed within the ullage port D、an above-deck datum，usually the top of the ullage hole

点击查看答案

第10题

[单选题] The internal volume of a cargo hold measured from the inside faces of the cargo battens，the lower side of the deck beams，and the top of the tank top ceiling is known as the（）.

A、gross tonnage B、deadweight space C、bale cubic D、stowage area

点击查看答案

账号：登录

答题记录

我的收藏

我的题库

客服

TOP

请使用微信扫码支付

订单号：
遇到问题请联系在线客服