Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts.<br /> Which commands are required for proper functioning of OSPF in this case?（）..

第1题

A、hostname R1 B、name R1 C、router name R1 D、name router R1

第2题

[] Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （） Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）

A、A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0 B、B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0 C、C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0 D、D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0 E、E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0 F、F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0

点击查看答案

第3题

[多选题] Which series of commands will configure router R1 for LAN-to-LAN communication with router R2？ The enterprise network address is 192.1.1.0/24 and the routing protocol in use is RIP.（）

A、R1（config）# interface ethernet 0；R1（config-if）# ip address 192.1.1.129 255.255.255.192；R1（config-if）# no shutdown B、R1（config）# interface ethernet 0；R1（config-if）# ip address 192.1.1.97 255.255.255.192；R1（config-if）# no shutdown C、R1（config）# interface serial 0；R1（config-if）# ip address 192.1.1.4 255.255.255.252；R1（config-if）# clock rate 56000 D、R1（config）# interface serial 0；R1（config-if）# ip address 192.1.1.6 255.255.255.252；R1（config-if）# no shutdown E、R1（config）# router rip；R1（config-router）# network 192.1.1.4；R1（config-router）# network 192.1.1.128 F、R1（config）# router rip；R1（config-router）# version 2；R1（config-router）# network 192.1.1.0

点击查看答案

第4题

[单选题] Refer to the exhibit. All routers have Protocol Independent Multicast (PIM) enabled interfaces. On the basis of the configuration provided on routers R1 and R2, which router will take on the func tion of rendezvous point (RP) for the multicast network? （）

A、both routers R1 and R2 B、router R1 C、router R2 D、none of the routers since they are not configured with static RP

点击查看答案

第5题

[单选题] Refer to the exhibit. OSPF has been configured on all routers in the network. However, router R1 does not receive a default route to router R2 as in tended. Which configuration change would ensure that R1 would receive a default route from R2? （）

A、Add the area 1 stub command on routers R1. B、Add the always keyword to the default - information originate configuration command on router R2. C、Remov e the default information originate configuration command from router R2 and place it on router R1. D、Add the ip route 5.0.0.0 255.255.255.0 0.0.0.0 command to router R2.

点击查看答案

第6题

[单选题] Refer to the exhibit. Router R1 is connected to networks 172.1 6.1.0 /26 and 172.16.1.64 /27. On the basis of the partial output in the exhibit, which statement is true? （）

A、Router R1 will deny the 172.16.1.0/26 route while permitting the 172.16.1.64/27 route to be advertised. B、Router R1 will advertise both rou tes. C、Router R1 should be reconfigured with an ACL instead of an ip prefix - list command. D、Router R1 will deny the 172.16.1.0/27 route while permitting the 172.16.1.0/26 route to be advertised.

点击查看答案

第7题

[单选题] Refer to the exhibit. OSPF is configured on all routers in the network. On the basis of the show ip ospf n eighbor output, what prevents R1 from establishing a full adjacency with R2? （）

A、Router R1 will only establish full adjacency with the DR and BDR on broadcast multi- access networks. B、Router R2 has been elected as a DR for the broadcast multiaccess network in OSPF area 1. C、Routers R1 and R2 are configured as stub routers for OSPF area 1 and OSPF area 2. D、Router R1 and R2 are configured for a virtual link between OSPF area 1 and OSPF area 2. E、The Hello parameters on routers R1 and R2 do not m atch.

点击查看答案

第8题

[单选题] Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR, and dynamically discover OSPF neighbors?（）

A、ip ospf network broadcast B、ip ospf network non - broadcast C、ip ospf network point - to - multipoint D、ip ospf network point - to - multipoint non - broadcast

点击查看答案

第9题

[单选题] Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface. What command would make this router not use a DR and require static OSPF neighbor definition?（）

A、ip ospf network broadcast B、ip ospf netw ork non - broadcast C、ip ospf network point - to - multipoint D、ip ospf network point - to - multipoint non - broadcast

点击查看答案

请使用微信扫码支付