搜题
用户您好， 请在下方输入框内搜索其它题目：
搜题
题目内容 （请给出正确答案）
提问人：网友 发布时间：
【单选题】

The （）is not a component of an oil separator.

A、sliding bowl bottom

B、gravity disc

C、separating disc

D、scum valve

查看正确答案
更多“The （）is not a component of an oil separator.”相关的问题
第1题
[单选题] The ping loopback hangs with no output.Which of the following is the most likely cause?（）

A、The loopback interface is down and resolv.conf is configured.  B、The loopback is not in /etc/hosts and resolv.conf is configured.  C、The loopback interface is down and resolv.conf is not configured.  D、The loopback is not in /etc/hosts and resolv.conf is not configured.  

点击查看答案
第2题
[单选题] An administrator is adding memory to a server. Once the system boots up, the same amount of memory appears as before the upgrade. Which of the following is the MOST likely cause?（）

A、The memory is not the correct CAS latency.  B、The memory is not installed in the correct slot.  C、The memory does not have the correct timing.  D、The memory is not the correct speed.  

点击查看答案
第3题
[单选题] Refer to the exhibit. A new TAC engineer came to you for advice. A GRE over IPsec tunnel was configured, but the tunnel is not coming up. W hat did the TAC engineer configure incorrectly?（）

A、The crypto isakmp configuration is not correct.  B、The crypto map configuration is not correct.  C、The interface tunnel configuration is not correct.  D、The network configuration is not correct; netw ork 172.16.1.0 is missing.  

点击查看答案
第4题
[单选题] An administrator has just installed a new NIC into the server. The system POSTs fine and the NIC is recognized by the OS, but it does not receive an IP address. Which of the following is the MOST likely cause of this?（）

A、The NIC is not on the HCL.  B、The driver is incorrect on the server.  C、The patch cable has not been seated properly.  D、The NIC is not seated properly.  

点击查看答案
第5题
[] Click the Exhibit button. Referring to the exhibit, you are not able to telnet to 192.168.10.1 from client PC 192.168.10.10.What is causing the problem?（） Click the Exhibit button. Referring to the exhibit, you are not able to telnet to 192.168.10.1 from client PC 192.168.10.10.What is causing the problem?（）

A、A. Telnet is not being permitted by self policy.  B、B. Telnet is not being permitted by security policy.  C、C. Telnet is not allowed because it is not considered secure.  D、D. Telnet is not enabled as a host-inbound service on the zone  

点击查看答案
第6题
[单选题] There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers: From your observations of the above exhibit, what is the underlying cause of the problem?（）

A、The loopback is not set.  B、The serial cable is faulty.  C、The subnet mask is not configured properly.  D、The IP address is not configured properly.  E、The Layer 2 frame types are not compatible.  F、The keepalive setting is not configured properly.  

点击查看答案
第7题
[单选题] If the buyer charters a ship and sends for the goods，the transit（）by shipment of the goods，although the seller does not know where the goods are being taken.

A、is terminated  B、is stopped  C、is not terminated  D、is not stopped  

点击查看答案
第8题
[单选题] You are not able to telnet to the interface IP of your JUNOS software with enhanced services devicefrom a PC on the same subnet. What is causing the problem? （）

A、Telnet is not being permitted by self policy.  B、Telnet is not being permitted by security policy.  C、Telnet is not allowed because it is not considered secure.  D、Telnet is not enabled as a host-inbound service on the zone.  

点击查看答案
第9题
[单选题] When Bob, a technician, powers up a desktop PC, the unit will repeat three short beeps and will not POST. Which of the following is MOST likely the problem?（）

A、The memory is failing.  B、The CPU is overheating.  C、The hard drive is not attached properly.  D、The operating system is not installed.  

点击查看答案
第10题
[单选题] The system hangs at boot time after starting NFS services.What is the most likely cause?（）

A、The action parameter of rcnfs in /etc/inittab is 'off' and the script called is not exiting.  B、The action parameter of rcnfs in /etc/inittab is 'wait' and the script called is not exiting.  C、The action parameter of rcnfs in /etc/inittab is 'once' and the script called is not exiting.  D、The action parameter of rcnfs in /etc/inittab is 'respawn' and the script called is not exiting.  

点击查看答案
账号：
答题记录 我的收藏 我的题库
客服
TOP

请使用微信扫码支付

订单号：
遇到问题请联系在线客服