The switches shown in the diagram, Core and Core2, are both Catalyst 2950s. The addressing scheme for each company site is as follows:Router Ethernet port - 1st usable addressCore - 2nd usable addressCore2 - 3rd usable addressFor this network, which of the following commands must be configured on Core2 to allow it to be managed remotely from any subnet on the network? （）<br /> <img src="https://nimg.ppkao.com/2018-07/ppweb/2018072315012336171.png?sign=65c23351793ef8742ab493d9f9aea718&t=62d48a62" />..

第1题

[] Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? （） Refer to the diagram. Which three statements describe the router port configuration and the switch port configuration as shown in the topology? （）

A、A.The Router1 WAN port is configured as a trunking port. B、B.The Router1 port connected to Switch1 is configured using subinterfaces. C、C.The Router1 port connected to Switch1 is configured as 10 Mbps. D、D.The Switch1 port connected to Router1 is configured as a trunking port. E、E.The Switch1 port connected to Host B is configured as an access port. F、F.The Switch1 port connected to Hub1 is configured as full duplex.

点击查看答案

第2题

[多选题] Refer to the topology shown in the exhibit. Which ports will be STP designated ports if all the links are operating at the same bandwidth? （）

A、Switch A - Fa0/0 B、Switch A - Fa0/1 C、Switch B - Fa0/0 D、Switch B - Fa0/1 E、Switch C - Fa0/0 F、Switch C - Fa0/1

点击查看答案

第3题

[多选题] Refer to the topology shown in the exhibit. Which ports will be STP designated ports if all the links are operating at the same bandwidth? （）

A、Switch A - Fa0/0 B、Switch A - Fa0/1 C、Switch B - Fa0/0 D、Switch B - Fa0/1 E、Switch C - Fa0/0 F、Switch C - Fa0/1

点击查看答案

第4题

[] Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the most likely reason that interface FastEthernet 0/10 is not the root port for VLAN 2?（） Refer to the exhibit. Given the output shown from this Cisco Catalyst 2950, what is the most likely reason that interface FastEthernet 0/10 is not the root port for VLAN 2?（）

A、A.This switch has more than one interface connected to the root network segment in VLAN 2. B、B.This switch is running RSTP while the elected designated switch is running 802.1d Spanning Tree. C、C.This switch interface has a higher path cost to the root bridge than another in the topology. D、D.This switch has a lower bridge ID for VLAN 2 than the elected designated switch.

点击查看答案

第5题

[多选题] Refer to the exhibit. The output that is shown is generated at a switch. Which three of these statements are true? （）

A、All ports will be in a state of discarding, learning, or forwarding. B、Thirty VLANs have been configured on this switch. C、The bridge priority is lower than the default value for spanning tree. D、All interfaces that are shown are on shared media. E、All designated ports are in a forwarding state. F、The switch must be the root bridge for all VLANs on this switch.

点击查看答案

第6题

[单选题] Refer to the exhibit.All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?（）

A、The access link needs to be configured in multiple VLANs. B、The link between the switches is configured in the wrong VLAN. C、The link between the switches needs to be configured as a trunk. D、VTP is not configured to carry VLAN information between the switches. E、Switch IP addresses must be configured in order for traffic to be forwarded between the switches

点击查看答案

第7题

[单选题] Based on the network shown in the graphic which option contains the potential networking problem and protocol or setting that can to prevent the problem?（）

A、Routing loops, hold down timers B、Switching loops, split horizon C、Routing loops, split horizon D、Switching loops, VTP E、Routing loops, STP F、Switching loops, STP

点击查看答案

第8题

[] Refer to the exhibit. MPLS has been enabled on router PE11. Which of these statements is correct regarding the output display shown in the exhibit? （） Refer to the exhibit. MPLS has been enabled on router PE11. Which of these statements is correct regarding the output display shown in the exhibit? （）

A、A. CEF switching is not needed for MPLS operation. B、B. CEF switching is only needed to forward labeled packets. C、C. CEF switching is needed on both ingress and egress interfaces on which MPLS is enabled. D、D. Interface-level CEF switching is needed only on egress interfaces that are sending IP packets on which the egress LSR performs the label imposition process. E、E. Interface-level CEF switching is needed only on ingress interfaces that are receiving IP packets on which the ingress LSR performs the label imposition process.

点击查看答案

第9题

[单选题] How many broadcast domains are shown in the graphic assuming only the default vlan is configured on the switches?（）

A、one B、six C、twelve D、two

点击查看答案

第10题

[单选题] How many broadcast domains are shown in the graphic assuming only the default vlan is configured on the switches?（）

A、one B、six C、twelve D、two

点击查看答案

请使用微信扫码支付